Dual Band Long Range AP

Technical Specification

Hardware

RF: 2.4 and 5 GHz Frequency Bands

Standard: IEEE 802.11a/b/g/n

Radio I: 11b/g/n: 2.412~2.484 GHz

Radio II: 11a/n: 5.18-5.24 and 5.26-5.32 and 5.5-5.7 and 5.745-5.825 GHz

Data Rate: Up to 300 Mbps in both frequency bands

Memory: 64MB

Flash Memory: 8MB

Antenna

Four (4) External 5 dBi Omni-Directional Antennas

Physical Interface

1 x RJ-45 Gigabit Ethernet (10/100/1000 Mbps)

1 x Reset Button

Power Jack

Power Requirements

Power Supply: 90 to 240 VDC ± 10%, 50/60 Hz

(depends on different countries)

Active Ethernet (Power-over-Ethernet, IEEE 802.3at/af)

Power Adapter (United States) 48VDC/0.375A

Device: 12V/2A

Modulations

OFDM: BPSK, QPSK, 26-OAM, 64-QAM, DBPSK, DQPSK, CCK

Operating Channels

2.4 GHz: US/Canada 1-11

5 GHz: Country dependent for the following ranges:

36, 40, 44, 48, 52, 56, 60, 64, 100, 104, 108, 112, 116, 120, 124, 128, 132, 136, 140, 149, 153, 157, 161, 165

Receiver Sensitivity

802.11n (5 GHz)

-94dBm @ MCS0

-76dBm @ MCS7

-91dBm @ MCS8

-73dBm @ MCS15

802.11n (2.4 GHz)

-95dBm @ MCS0

-77dBm @ MCS7

-91dBm @ MCS8

-75dBm @ MCS15

802.11a (5 GHz)

-95dBm @ 6Mbps

-80dBm @ 54Mbps

802.11b (2.4 GHz)

-95dBm @ 1Mbps

-91dBm @ 11Mbps

Available Transmit Power

(Max. Power may be different depending on local regulations)

802.11n (5 GHz) 802.11n (2.4 GHz)

27dBm @ MCS0~2/MCS8~10 27dBm @ MCS0~2/MCS8~10

26dBm @ MCS3/MCS11 27dBm @ MCS3/MCS11

25dBm @ MCS4/MCS12 26dBm @ MCS4/MCS12

23dBm @ MCS5/MCS13 25dBm @ MCS5/MCS13

22dBm @ MCS6/MCS14 24dBm @ MCS6/MCS14

21dBm @ MCS7/MCS15 23dBm @ MCS7/MCS15

802.11a (5 GHz) 802.11b (2.4 GHz)

26dBm @ 6~24Mbps 7dBm @ 1~11Mbps

25dBm @ 36Mbps

23dBm @ 48Mbps

21dBm @ 54Mbps

Software

Topology Infrastructure/Ad-Hoc

Operation Modes Access Point, WDS Bridge, WDS Access Point, Universal Repeater

Multiple BSSID Supports up to 8 BSSIDs per radio

LAN IP (check validity and DHCP server IP range) MAC

SSID-to-VLAN Tagging Supports 802.1q SSID-to-VLAN tagging

Spanning Tree Supports 802.1d Spanning Tree Protocol

Wireless

Wireless Mode: 11a/11b/11g/11n

Channel selection (settings vary by country)

Channel bandwidth (Auto, 20 MHz, 40 MHz)

Transmission rate:

2.4 GHz: 11n only, 11b/b/n mix, 11b only, 11b/g, 11g only

5 GHz: 11n only, 11a/n mix, 11a only

QoS WMM (Wireless Multimedia)

VPN Pass-through (PPTP, L2TP, IPSec)

WPS Software only

Management

Tx Power Control Adjust transmit power by dBm

Configuration Web-based configuration (http)/Telnet

Telnet Server CLI

Firmware Upgrade Via web browser, settings are reserved after upgrade

Administrator Setting Administrator Username and Password Change

Reset Setting

Reboot (press 1 second).

Reset to factory default (press 10 seconds)

System Monitoring Status Statistic and Event Log

SNMP V1, V2c, V3

MIB MIB I, MIB II (RFC1213) and private MIB

Traffic Shaping Incoming and outgoing wireless traffic shaping

Auto-channel Selection Automatically selecting least congested channel

Bandwidth Measurement IP range and bandwidth management

Auto Reboot Reboot Access Point by minute, hour, day, or week

Backup and Restore Save and restore settings through Web interface

CLI Supports Command Line Interface

Diagnosis IP pinging statistics

Log SysLog and Local Log support

LED Control On/Off

AP Detection Scanning for available EnGenius APs

Wireless Security

WPA/WPA2 Personal (WPA-PSK using TKIP or AES)

WPA/WPA2 Enterprise (WPA-EAP using TKIP)

802.1X RADIUS Authenticator: MD5/TLS/TTLS, PEAP

SSID broadcast enable/disable

MAC Address Filtering, Up to 50 field

L2 Isolation (Access Point mode)

Wireless STA (Client) connected list (Idle/Connection Time, Pkt statistics)